Electronic Schematics
FM Transmitters
PLL Synthesizers
Stereo Encoders & Decoders
Antennas
FM Receivers
Audio / Amplifiers
Power Supplies
AC/DC Inverters AC/DC Converters
Battery Chargers
Remote Control
PC Related
Test & Measurement
PIC / ATMEL / AVR
USB Circuits
Telephone Related
LED
Miscellaneous Circuits
Stepper Motors

 Schematics  >>  Remote Control

Page 1 of 4:   1   2   3   4
4-CH RF Remote Control
Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and it works even through the walls. You can control many low voltage gadgets including motors, RC cars, robotic devices, amplifiers or 110V/220V appliances through relays such as lights, fans, AC systems, home appliances, garage doors, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of. 4-CH RF remote control is used to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either toggle or momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly such us motors or be connected to either 5V or 12V relays to control appliances that use 110V / 220V mains voltage or any voltage of your choice. Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote. It is also possible to use several remotes to control the same appliance such as garage door.


2 Channel RF AVR Remote Control
How many times you needed some remote control to handle some electric device ? many times. There are lot of remote controls like infrared, RF, SMS (like my other circuit) and more. The basic small-range remote controls are 2, Infrared and RF (Radio Frequency). One of the weaks of Infrared is that the signal can not pass the walls. So, if you want to control your garage door, the only way is to use some RF remote control. The circuit (transmitter and receiver) use few components and ordinary (I love few component circuits) . Its easy to build it because you don't have to tune-up any coil or variable capacitor. The RF modules are fix to work in 418MHz area.


2-CH RF Remote Control
On these pages, I will introduce Remote Controller with Radio Frequency. The electric wave sending-out is controlled with the code by PIC for transmission and the code is deciphered by PIC for receiving.


2-Channel IR Relay Controller
This project is a 2 channel infrared (IR) remote controlled relay driver with power saving. It works with 12-bit SIRC IR signals as used by Sony remote controls. The board uses Microchip's low cost PIC10F200 microcontroller along with a handful of easy to find components making this possibly the lowest cost remote controlled relay driver around.


3 Channel IR Remote Control
This project is a 3-channel IR remote control with 3 output relay and easy to build. Features: CPU PIC12F629 at 4MHz crystal for Tx/Rx, 3 channel output relay, The Tx use sleep mode for saving battery power, Use Phillips RC5 protocol, distance more than 7 m, Easy circuit to build and assembly and small amount of components. Uses RC5 protocol which is probably the most used by hobbyists, probably because the wide availability of cheap remote controls and easy to understand.


3 Channel RF Remote Control
This is a 3 channel RF remote control project.The transmitter powered by 3V battery(coin size) range about 10 m. This remote control I use PIC12F509 from Microchip which is a 8-pin single-chip microcontroller designed for low pin count applications with 1 K words flash memory and 41Byte SRAM and some special features such Power-saving Sleep mode,Wake-up from Sleep on pin change.


8 channel IR remote control
This IR remote control that you can use to control other devices or circuits up to 8 devices. The control codes are sent in RC5 format modulated to about 38 kHz carrier frequency.The IR transmitter powered by the CR2016 which is a 3V button Cells Battery CR2016. To extend the life of the battery this is done by putting the CPU into SLEEP mode for most of the time and wake-up only when a key is pressed.


8 Channel IR Remote Control
This IR remote control that you can use to control other devices or circuits up to 8 devices. The control codes are sent in RC5 format modulated to about 38 kHz carrier frequency.The IR transmitter powered by the CR2016 which is a 3V button Cells Battery CR2016.To extend the life of the battery this is done by putting the CPU into SLEEP mode for most of the time and wake-up only when a key is pressed. PIC16F630 is the heart of the transmitter used to send IR command to receiver.It also generate 38KHz carrier frequency.The CR2016 is 3V battery which is supply for the circuit. When any key not pressed the CPU work in SLEEP mode to reduce baterry power consumption and wake-up only when any key pressed. To wake-up the CPU from SLEEP mode the CPU use interrupt on change feature which interrupted when the state on PORTA change then the program execution after an interrupt is at the interrupt vector, if the global interrupt is not enabled, the program starts executing the first line of code right after the SLEEP instruction.In the interrupt service routine the software will scan the key that pressed and send IR command appropriate with key pressed.


8 Channel RF Remote Control
This is an 8 Channel RF Remote Transmitter and Receiver that will allow to remotely control various electronic projects. RF Remote Control provides 2 latched and 6 momentary outputs that could be used to control your favorite devices such as amplifier, robotic devices, RC cars, computer, home appliances, lamps and many other cool gadgets.


8 Channel RF Remote Control
This is a 8 channel RF remote control project. The transmitter powered by 5V.the RF module I used had long start-up and power down period after receiving a high pulse. To counter all of this I kept the receiver in constant standby mode, but sending a information all the time. That way the noise is flooded out, and the receiver will always respond. I had been trying all sorts of error detection methods and different ways of encoding the bytes, when I just gave up. Since the link is so noisy I decided to cut out all of the error detection methods and just make it accept anything it receives, and see what happened from there. But what do you know, it worked!


Page 1 of 4:   1   2   3   4


Accurate LC Meter Capacitance Inductance Meter with 16F628 and LCD
Volt Ampere Meter with 16F876 Microcontroller and LCD display
 
Accurate LC Meter

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings.
PIC Volt Ampere Meter

Volt Ampere Meter measures voltage of 0-70V or 0-500V with 100mV resolution and current consumption 0-10A or more with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with 16x2 backlighted LCD.

50MHz 60MHz Frequency Meter / Counter with 16F628 & LCD
1Hz - 2MHz XR2206 Function Generator
60MHz Frequency Meter / Counter

Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.
1Hz - 2MHz XR2206 Function Generator

1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

BA1404 HI-FI Stereo FM Transmitter
USB IO Board PIC18F2455 / PIC18F2550
BA1404 HI-FI Stereo FM Transmitter

Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter broadcasts high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
USB IO Board

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible.

RF Remote Control 433MHz Four Channel
100m 4-Channel 433MHz Wireless RF Remote Control
 
200m 4-Channel 433MHz Wireless RF Remote Control

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
100m 4-Channel 433MHz Wireless RF Remote Control

Four button RF remote is used to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either toggle or momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly or be connected to either 5V or 12V relays (or motors) to control appliances that use 110V / 220V mains voltage or any voltage of your choice. Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote. It is also possible to use several remotes to control the same appliance such as garage door.
 
 Latest Schematics
Curious C-Beeper
Automatic Night Light
LM386 Utility Amplifier
Mini FM Transmitter
Automatic Garden Light
USB Battery Pack
Phone Transmitter
27MHz Walkie Talkie
Plant Water Alarm
4km FM Transmitter
1 Watt FM Transmitter Amplifier
Simple MOSFET Switch
AM Radio Transmitter Using 555 Chip
Adjustable Bench Power Supply
Arduino RF link using 433MHz Transmitter / Receiver modules
MAX038 Generator
Adjustable Constant Current Load
68W LM3886 Amplifier
18W FM Transmitter
Solar Charger for USB Devices
500W Modified Sine Wave Inverter
3.3V and 5V Power Supply
Veronica 1W FM Transmitter
Transformerless Joule Thief
1W PLL Transmitter with MC145152
Eliminating LED Christmas Lights Flicker
100m Simple FM Transmitter
PCM5102 Burr-Brown DAC with DIR9001 SPDIF Receiver
Simple FM Transmitter with BC549
Simple MP3 FM Transmitter

Electronics-DIY.com © 2002-2014. All Rights Reserved.