BH1417 USB FM Transmitter
 
BH1417 USB FM Transmitter


 

BH1417 USB FM Transmitter

 


Here's BH1417 USB FM Transmitter with built-in PLL circuit. Its low-frequency signal is converted into high-frequency, which can take any audio device with FM radio (stereo, car CD, MP3, DVD player, etc.), as a normal radio station. Transmitter power is sufficient for reliable reception of its signal within a few tens of meters. The basis of the device is a chip BH1417F, included in a typical scheme. This device contains all the necessary circuitry to generate a composite stereo signal c of the pilot tone, the RF generator with PLL and power amplifier. A detailed description is given in.


BH1417 USB FM Transmitter

BH1417 specs and features chips:
- Supply voltage 4 … 6 volt;
- Current consumption 20 mA;
- Operating temperature range -40 … +85 ° C;
- A range of audio frequencies 20Hz … 15kHz;
- 40 dB channel separation;
- THD 0.1%.

Formation of carrier frequencies in the broadcast signal chip carries a stabilized quartz resonator Z1 (7.6MHz) PLL-synthesizer with 4-bit parallel interface control. Changing the position of switches SA1 … SA4 can get 14 discrete frequencies. Their values are listed in the table.

This device PLL is stable only works in one of the sub-bands (87.7MHz … 88.9MHz or 106.7MHz … 107.9MHz) without having to reconfigure L1. Structurally, the device is on the circuit board 50 x 23mm and is equipped with a USB connector, through which the supplied 5V. The photographs shows the appearance of printed circuit board unit.

The PCB is made of fiberglass-sided 1.0 mm thick. All resistors, inductor L2 and Ceramic Capacitors – SMD, 0805. As the VT1, VT2, you can use npn transistors for surface mounting with a static gain of at least 100. Crystal at 7.6 MHz can be purchased at the store “Quartz” 50m from the metro station “road enthusiasts” (Sh Enthusiasts, 31). You can also use less scarce, the frequency of 7.68 MHz. The coil loop oscillator L1 is wound on a frame of 4 mm diameter tinned copper wire with a diameter of 0.6 mm has 4.5 turns in the winding length of 6 mm. Within the framework of core trimming high ferrite.

It should be noted that the independent production and installation of such a board problem is rather complicated. A simpler version of the printed circuit board can be found in [2]. When first turned on and set power 5.1 V is supplied from a laboratory source. To get started, choose the sub-band switch SA4, which will operate the transmitter. Then, turning off the SA3 (on pin. 17 circuits DA1 to be a logical unit) and adding SA1 and SA2 (at the pin. 15 and 16 must be logic zeros) adjusting core coils L1, seeking to Pin 7 voltage 2.8 V. After that, the FM receiver check the stability of the PLL capture within the sub-band. To do this, changing the position of the switches SA1 … SA3, check for the receiver of the transmitted signal at all frequencies sub-band.

In conclusion, the maximum undistorted signal is selected value of resistors R1 and R2 (structurally they are located inside the input jack). The device is preferably placed in a screen of thin sheet metal, perhaps after this it is necessary to adjust the L1. As a piece of wire antenna and MGTF-0, 07 length of about 80cm. When choosing the operating frequency to avoid interference is desirable that it defended by no less than 200 kHz operating in your area FM radio stations and broadcast television channels.


BH1417 USB FM Transmitter Schematic
BH1417 USB FM Transmitter PCB Layout


BH1417 USB FM Transmitter





Accurate LC Meter Capacitance Inductance Meter with 16F628 and LCD
Volt Ampere Meter with 16F876 Microcontroller and LCD display
 
Accurate LC Meter

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings.
PIC Volt Ampere Meter

Volt Ampere Meter measures voltage of 0-70V or 0-500V with 100mV resolution and current consumption 0-10A or more with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with 16x2 backlighted LCD.

50MHz 60MHz Frequency Meter / Counter with 16F628 & LCD
1Hz - 2MHz XR2206 Function Generator
60MHz Frequency Meter / Counter

Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.
1Hz - 2MHz XR2206 Function Generator

1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

BA1404 HI-FI Stereo FM Transmitter
USB IO Board PIC18F2455 / PIC18F2550
BA1404 HI-FI Stereo FM Transmitter

Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter broadcasts high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
USB IO Board

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible.

ESR Meter / Transistor Tester Kit
Audiophile Headphone Amplifier Kit
 
ESR Meter / Capacitance / Inductance / Transistor Tester Kit

ESR Meter kit is an amazing multimeter that measures ESR values, capacitance (100pF - 20,000uF), inductance, resistance (0.1 Ohm - 20 MOhm), tests many different types of transistors such as NPN, PNP, FETs, MOSFETs, Thyristors, SCRs, Triacs and many types of diodes. It also analyzes transistor's characteristics such as voltage and gain. It is an irreplaceable tool for troubleshooting and repairing electronic equipment by determining performance and health of electrolytic capacitors. Unlike other ESR Meters that only measure ESR value this one measures capacitor's ESR value as well as its capacitance all at the same time.
Audiophile Headphone Amplifier Kit

Audiophile headphone amplifier kit includes high quality audio grade components such as Burr Brown OPA2134 opamp, ALPS volume control potentiometer, Ti TLE2426 rail splitter, Ultra-Low ESR 220uF/25V Panasonic FM filtering capacitors, High quality WIMA input and decoupling capacitors and Vishay Dale resistors. 8-DIP machined IC socket allows to swap OPA2134 with many other dual opamp chips such as OPA2132, OPA2227, OPA2228, dual OPA132, OPA627, etc. Headphone amplifier is small enough to fit in Altoids tin box, and thanks to low power consumption may be supplied from a single 9V battery.
 

Arduino Prototype Kit
RF Remote Control 433MHz Four Channel
 
Arduino Prototype Kit

Arduino Prototype is a spectacular development board fully compatible with Arduino Pro. It's breadboard compatible so it can be plugged into a breadboard for quick prototyping, and it has VCC & GND power pins available on both sides of PCB. It's small, power efficient, yet customizable through onboard 2 x 7 perfboard that can be used for connecting various sensors and connectors. Arduino Prototype uses all standard through-hole components for easy construction, two of which are hidden underneath IC socket. Board features 28-PIN DIP IC socket, user replaceable ATmega328 microcontroller flashed with Arduino bootloader, 16MHz crystal resonator and a reset switch. It has 14 digital input/output pins (0-13) of which 6 can be used as PWM outputs and 6 analog inputs (A0-A5). Arduino sketches are uploaded through any USB-Serial adapter connected to 6-PIN ICSP female header. Board is supplied by 2-5V voltage and may be powered by a battery such as Lithium Ion cell, two AA cells, external power supply or USB power adapter.
200m 4-Channel 433MHz Wireless RF Remote Control

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
 

Electronics-DIY.com © 2002-2017. All Rights Reserved.