| |
|
FREE SHIPPING ON ALL ORDERS OVER $99 |
|
4-Channel 433MHz Wireless RF Remote Control Kit (200m)
Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
Four button RF remote is used to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either toggle or momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly or be connected to 5V / 12V / 24V relays to control appliances that use 110V / 220V mains voltage or any voltage of your choice.
Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote. It is also possible to use several remotes to control the same appliance such as garage door.
Click here for remote control schematic and description
Specifications
Output Mode: Toggle / Momentary
Transmission Frequency: 433MHz
Kit Voltage Supply: 5 - 24V
Relay Types: 5V / 12V / 24V
Receiver Dimensions: 45mm x 30mm x 7mm
Remote Control Dimensions: 52 mm x 40 mm x 14 mm (when antenna is not extended)
Component List
1x 4-Channel RF Remote Control Transmitter with 12V alkaline battery cell
1x 4-Channel RF Receiver
1x Printed Circuit Board (PCB)
1x PIC16F628A Programmed Microcontroller
1x 78L05 Voltage Regulator
1x 10uF Capacitor
1x 100n Ceramic Capacitor
4x BC549 Transistors
4x 1K Resistors
4x 1N4148 Protection Diodes
5x 2-PIN Headers
1x Instructions Manual |
|
|
|
4-Channel 433MHz Wireless RF Remote Control Kit (100m)
Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 100m / 325ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
Four button RF remote is used to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either toggle or momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly or be connected to 5V / 12V / 24V relays to control appliances that use 110V / 220V mains voltage or any voltage of your choice.
Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote. It is also possible to use several remotes to control the same appliance such as garage door.
Click here for remote control schematic and description
Specifications
Output Mode: Toggle / Momentary
Transmission Frequency: 433MHz
Kit Voltage Supply: 5 - 24V
Relay Types: 5V / 12V / 24V
Receiver Dimensions: 45mm x 30mm x 7mm
Remote Control Dimensions: 52 mm x 40 mm x 14 mm (when antenna is not extended)
Component List
1x 4-Channel RF Remote Control Transmitter with 12V alkaline battery cell
1x 4-Channel RF Receiver
1x Printed Circuit Board (PCB)
1x PIC16F628A Programmed Microcontroller
1x 78L05 Voltage Regulator
1x 10uF Capacitor
1x 100n Ceramic Capacitor
4x BC549 Transistors
4x 1K Resistors
4x 1N4148 Protection Diodes
5x 2-PIN Headers
1x Instructions Manual |
|
|
|
4-Channel 433MHz Wireless RF Remote Control Kit (200m) - Momentary
Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
Four button RF remote is used to turn ON / OFF four different devices independently. All four outputs work independently in momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly or be connected to 5V /12V / 24V relays to control appliances that use 110V / 220V mains voltage or any voltage of choice.
Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote.
Click here for remote control schematic and description
Specifications
Output Mode: Momentary
Transmission Frequency: 433MHz
Kit Voltage Supply: 5 - 24V
Relay Types: 5V / 12V / 24V
Receiver Dimensions: 45mm x 30mm x 7mm
Remote Control Dimensions: 52 mm x 40 mm x 14 mm (when antenna is not extended)
Component List
1x 4-Channel RF Remote Control Transmitter with 12V alkaline battery cell
1x 4-Channel RF Receiver
1x Printed Circuit Board (PCB)
1x PIC16F628A Programmed Microcontroller
1x 78L05 Voltage Regulator
1x 10uF Capacitor
1x 100n Ceramic Capacitor
4x BC549 Transistors
4x 1K Resistors
4x 1N4148 Protection Diodes
5x 2-PIN Headers
1x Instructions Manual |
|
|
|
1000m 433MHz RF Transmitter Module
This tiny RF Transmitter module is great for building your own wireless remote control or wireless link. Remote control that allows to control different devices can be easily implemented with wide range of encoder/decoder chips (such as HOLTEK HT12E + HT12D or MC145026 + MC145027 available in our store) or PIC / AVR microcontrollers. RF Module can also be used for sending data at up to 9.6KB/s.
RF Transmitter Specifications:
TTL Compatible Input
Voltage Supply: 3 - 12V
Power Consumption: 5 - 45mA
Quiescent Current: 20uA
Max Transfer Rate: 9.6KB/s
Operating Frequency: 433MHz
Transmitting Range: 1000m
Dimensions: 19mm x 19mm x 8mm |
|
|
|
433MHz RF Receiver Module
This tiny RF Receiver module is great for building your own wireless remote control or wireless link. Remote control that allows to control different devices can be easily implemented with wide range of encoder/decoder chips (such as HOLTEK HT12E + HT12D or MC145026 + MC145027 available in our store) or PIC / AVR microcontrollers. RF Module can also be used for sending data at up to 4.8KB/s.
RF Receiver Specifications:
TTL Compatible Output
Voltage Supply: 5V
Power Consumption: 5mA
Receiving Sensitivity: -103 dB
Max Transfer Rate: 4.8KB/s
Operating Frequency: 433MHz
Dimensions: 30mm x 14mm x 7mm |
|
|
|
4-Channel 433MHz Wireless RF Remote Control - 100m (Transmitter + Receiver)
4 Channel RF Remote Transmitter and Receiver allows to remotely control four appliances. RF Remote Control provides 4 momentary outputs that can be wired to relays and control home appliances, lights, motors, light dimmers, robotic devices, RC cars, computer, etc. RF transmitter provides up to 100m range. Selection of custom address codes (by soldering pins) allows to operate more than one remote control system in the same area or to control one receiver with multiple transmitters. If required momentary outputs can be converted to toggle with low cost digital 4013 IC. 12V (27A) alkaline battery is included.
Features:
4 Momentary Outputs
100m Transmission Range
Small Size
Rock-solid oscillator provides reliable operation
Valid transmission (VT) pin is energized if any button on the remote is pressed
High noise immunity
Terminal pins provide simple connection to power supply and four devices
Selection of custom address codes (by soldering pins) allows to operate more than one unit in the same area
RF Transmitter Specifications:
Voltage Supply: 12V (Included 27A Alkaline Battery)
Transmission Frequency: 433MHz
Transmission Range: 100m
Dimensions: 52 mm x 40 mm x 14 mm
RF Receiver Specifications:
Voltage Supply: 5V
Transmission Frequency: 433 MHz
Output Mode: Momentary
Power Consumption: 5 mA
Receiving Sensitivity: -101 dbm
Dimensions: 36 mm x 25 mm x 8 mm |
|
|
|
4-Channel 433MHz Wireless RF Remote Control - 200m (Transmitter + Receiver)
4 Channel RF Remote Transmitter and Receiver allows to remotely control four appliances. RF Remote Control provides 4 momentary outputs that can be wired to relays and control home appliances, lights, motors, light dimmers, robotic devices, RC cars, computer, etc. RF transmitter provides up to 100m range. Selection of custom address codes (by soldering pins) allows to operate more than one remote control system in the same area or to control one receiver with multiple transmitters. If required momentary outputs can be converted to toggle with low cost digital 4013 IC. 12V (27A) alkaline battery is included.
Features:
4 Momentary Outputs
200m Transmission Range
Small Size
Rock-solid oscillator provides reliable operation
Valid transmission LED status through VT connection
High noise immunity
Terminal pins provide simple connection to power supply and four devices
Selection of custom address codes (by soldering pins) allows to operate more than one unit in the same area
RF Transmitter Specifications:
Voltage Supply: 12V (27A Alkaline Battery)
Transmission Frequency: 433MHz
Transmission Range: 200m
Dimensions: 58 mm x 26 mm x 13 mm
RF Receiver Specifications:
Voltage Supply: 5V
Transmission Frequency: 433 MHz
Output Mode: Momentary
Power Consumption: 5 mA
Receiving Sensitivity: -101 dbm
Dimensions: 36 mm x 25 mm x 8 mm |
|
|
|
4-Channel 433MHz Wireless RF Receiver
This is an assembled 4 Channel RF Remote Receiver (without RF Remote Transmitter). RF Remote Control provides 4 momentary outputs that could be used to control your favorite devices such as amplifier's volume control, selection of audio sources, wireless light control, light dimmers, robotic devices, motors, RC cars, computer, home appliances, and many other cool gadgets. If required momentary outputs can be easily converted to toggle with 4013 digital low cost IC.
Features:
4 Momentary Outputs
Small Size
Rock-solid oscillator provides reliable operation
Valid transmission LED status through VT connection
High noise immunity
Terminal pins provide simple connection to power supply and four devices
Selection of custom address codes (by soldering pins) allows to operate more than one unit in the same area
RF Receiver Specifications:
Voltage Supply: 5V
Transmission Frequency: 433 MHz
Output Mode: Momentary
Power Consumption: 5 mA
Receiving Sensitivity: -101 dbm
Dimensions: 36 mm x 25 mm x 8 mm |
|
|
|
200m 4-Channel Remote Control Transmitter
This is an additional 4-Channel RF Remote Transmitter with 200m range for controlling 4-Channel 433MHz Wireless RF Receiver with multiple Remote Transmitters.
This product is compatible with 4-Channel 433MHz Wireless RF Receiver and 4-Channel Remote Control System with Four Relays.
Features:
4 Channels
200m Transmission Range
Small Size
Rock-solid oscillator provides reliable operation
Transmission LED status
High noise immunity
Selection of custom address codes (by soldering pins) allows to operate more than one transmitter or receiver in the same area
RF Transmitter Specifications:
Voltage Supply: 12V (Includes 27A Alkaline Battery)
Transmission Frequency: 433MHz
Transmission Range: 200m
Dimensions: 58 mm x 26 mm x 13 mm |
|
|
|
|