1 Watt PLL FM Broadcast Transmitter
 


 

1 Watt PLL FM Broadcast Transmitter

 


This is a 1 Watt PLL FM broadcast transmitter. The RF output varies from 500mW to about 1.2W depending on the frequency selected and RF output transistor used. Motorola 2N4427 always seems to work well. Transmitter uses CMOS PLL VCO that prevents the frequency drifts. The frequency is selected via DIP switches. The transmitter is supplied by 12V DC and can also be powered from the battery.


1 Watt PLL FM Broadcast Transmitter

This is a rather crude PCB layout i did using MS Paint. Not the best but it should work

This shows the test point for the PLL lock voltage. Ideally, it should be set for 3Volts (in the middle) using the oscillator coil. If the voltage doesn't change, oscillator may be at the end of its range in which case then c3 should be either increased slightly for a lower frequency and decreased for higher frequency. Try 22pf plus/minus 10pf

Component Values for VHF PLL

Resistors

R1 - 10K
R2 - 10K
R3 - 10K
R4 - 10K
R5 - 10K
R6 - 100R
R7 - 1K
R8 - 10K
R9 - 470R
R10 - 10K
R11 - 470R
R12 - 100R
R13 - 470R
R14 - 10K
R15 - 10R
R16 - 47R
R17 - 10R
R18 - 100K
R19 - 1K
R20 - 10K
R21 - 10K
R22 - 1M
R23 - 100K
R24 - 100K
R25 - 100R

RP1 - 9 Pin 100K Commoned Resistor array
RP2 - 9 Pin 100K Commoned Resistor array

Capacitors

C1 - 1uF electrolytic
C2 - 27pF ceramic
C3 - 22pF ceramic (tuning cap- change to extend tuning range)
C4 - 27pF ceramic
C5 - 100pF ceramic (101)
C6 - 100pF ceramic (101)
C7 - 100pF ceramic (101)
C8 - 1000uF electrolytic
C9 - 100nF ceramic (104)
C10 - 100nF ceramic (104)
C11 - 100pF ceramic (101)
C12 - 4.7pF ceramic
C13 - 100nF ceramic (104)
C14 - 100nF ceramic (104)
C15 - 100nF ceramic (104)
C16 - 100nF ceramic (104)
C17 - 100nF ceramic (104)
C18 - 39pF ceramic
C19 - 39pF ceramic
C20 - 39pF ceramic
C21 - 39pF ceramic
C22 - 1nF ceramic (102)
C23 - 10nF ceramic (103)
C24 - 47uF electrolytic
C25 - 1uF electrolytic
C26 - 10uF electrolytic
C27 - 100nF ceramic (104)
C28 - 100nF ceramic (104)
C29 - 100nF ceramic (104)
C30 - 100nF ceramic (104)
C31 - 100pF ceramic (101)
C32 - 100nF ceramic (104)
C33 - 47uF electrolytic
C34 - 100nF ceramic (104)

VC1 - 2..22pF green trimmer
VC2 - 5..60pF yellow trimmer
VC3 - 2..22pF green trimmer
VC4 - 2..22pF green trimmer

Inductors

L1 - Toko tuning coil with screening can 5.5 turns 100-075
L2 - Toko S18 Yellow
L3 - Toko S18 Yellow
L4 - Toko S18 Green
L5 - Toko S18 Green
L6 - Toko S18 Orange
L7 - Toko S18 Orange
L8 - RF choke 10uH-100uH

Semiconductors

VD1 - Variable capacitance diode
VD2 - Variable capacitance diode
VD3 - Variable capacitance diode
D1 - 1N4841
ZD1 -BZX 6.2V Zener Diode

Q1 - BSX20
Q2 - BSX20
Q3 - BSX20 (or ztx313 on older boards)
Q4 - BSX20 (or ztx313 on older boards)
Q5 - 2N4427 with clip on heatsink (Motorola will give more power)

74HC4024 - Binary Counter
74HC4060 - Binary counter with oscillator
74HC4046 - Phase locked loop IC
74HC4059 - Divide by N counter

Miscellaneous

6.4 Mhz Quartz Crystal
DIP1 - 8 Way DIL DIP Switch
DIP2 - 8 Way DIL DIP Switch

Update: I finally got round to redrawing this in EAGLE. You can download the EAGLE PCB files below.
Here are some 3D renders of the Gerber files.






1 Watt PLL FM Broadcast Transmitter

1 Watt PLL FM Broadcast Transmitter

1 Watt PLL FM Broadcast Transmitter




Accurate LC Meter Capacitance Inductance Meter with 16F628 and LCD
Volt Ampere Meter with 16F876 Microcontroller and LCD display
 
Accurate LC Meter

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings.
PIC Volt Ampere Meter

Volt Ampere Meter measures voltage of 0-70V or 0-500V with 100mV resolution and current consumption 0-10A or more with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with 16x2 backlighted LCD.

50MHz 60MHz Frequency Meter / Counter with 16F628 & LCD
1Hz - 2MHz XR2206 Function Generator
60MHz Frequency Meter / Counter

Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.
1Hz - 2MHz XR2206 Function Generator

1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

BA1404 HI-FI Stereo FM Transmitter
USB IO Board PIC18F2455 / PIC18F2550
BA1404 HI-FI Stereo FM Transmitter

Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter broadcasts high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
USB IO Board

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible.

ESR Meter / Transistor Tester Kit
Audiophile Headphone Amplifier Kit
 
ESR Meter / Capacitance / Inductance / Transistor Tester Kit

ESR Meter kit is an amazing multimeter that measures ESR values, capacitance (100pF - 20,000uF), inductance, resistance (0.1 Ohm - 20 MOhm), tests many different types of transistors such as NPN, PNP, FETs, MOSFETs, Thyristors, SCRs, Triacs and many types of diodes. It also analyzes transistor's characteristics such as voltage and gain. It is an irreplaceable tool for troubleshooting and repairing electronic equipment by determining performance and health of electrolytic capacitors. Unlike other ESR Meters that only measure ESR value this one measures capacitor's ESR value as well as its capacitance all at the same time.
Audiophile Headphone Amplifier Kit

Audiophile headphone amplifier kit includes high quality audio grade components such as Burr Brown OPA2134 opamp, ALPS volume control potentiometer, Ti TLE2426 rail splitter, Ultra-Low ESR 220uF/25V Panasonic FM filtering capacitors, High quality WIMA input and decoupling capacitors and Vishay Dale resistors. 8-DIP machined IC socket allows to swap OPA2134 with many other dual opamp chips such as OPA2132, OPA2227, OPA2228, dual OPA132, OPA627, etc. Headphone amplifier is small enough to fit in Altoids tin box, and thanks to low power consumption may be supplied from a single 9V battery.
 

Arduino Prototype Kit
RF Remote Control 433MHz Four Channel
 
Arduino Prototype Kit

Arduino Prototype is a spectacular development board fully compatible with Arduino Pro. It's breadboard compatible so it can be plugged into a breadboard for quick prototyping, and it has VCC & GND power pins available on both sides of PCB. It's small, power efficient, yet customizable through onboard 2 x 7 perfboard that can be used for connecting various sensors and connectors. Arduino Prototype uses all standard through-hole components for easy construction, two of which are hidden underneath IC socket. Board features 28-PIN DIP IC socket, user replaceable ATmega328 microcontroller flashed with Arduino bootloader, 16MHz crystal resonator and a reset switch. It has 14 digital input/output pins (0-13) of which 6 can be used as PWM outputs and 6 analog inputs (A0-A5). Arduino sketches are uploaded through any USB-Serial adapter connected to 6-PIN ICSP female header. Board is supplied by 2-5V voltage and may be powered by a battery such as Lithium Ion cell, two AA cells, external power supply or USB power adapter.
200m 4-Channel 433MHz Wireless RF Remote Control

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
 

Electronics-DIY.com © 2002-2017. All Rights Reserved.