HOME     STORE     BLOG     SCHEMATICS     TUTORIALS     DOWNLOADS     CONTACT

AVR ISP Programmer (In-Sytem programmer) for ATMEL
 
AVR ISP Programmer (In-Sytem programmer) for ATMEL


 

AVR ISP Programmer (In-Sytem programmer) for ATMEL

 


This AVR ISP original by ATMEL you can found on "AVR software and technical Library - April 2003" CD-rom. It small component count I design new PCB and change some component that easy to build small PCB. The new firmware was writen by John Samperi for AT90S2313. This code can program more devices.


AVR ISP Programmer (In-Sytem programmer) for ATMEL

Specification

- Device support

AT90Sxxxx ATtinyXX ATmegaXXXX
AT90S1200 rev. A*
AT90S1200 rev. B*
AT90S1200 rev. C*
AT90S1200*
AT90S2313*
AT90S2323*
AT90S2333
AT90S2343*
AT90S4414*
AT90S4433
AT90S4434
AT90S8515*
AT90S8535 ATtiny12
ATtiny15
ATtiny19
ATtiny28
ATtiny26 * ATmega8 *
ATmega8 BOOT *
ATmega16*
ATmega16 BOOT*
ATmega32*
ATmega32 BOOT*
ATmega64*
ATmega64 BOOT*
ATmega8515 *
ATmega8515 BOOT*
ATmega103
ATmega603
ATmega128
ATmega128 BOOT ATmega161
ATmega161 BOOT ATmega163
ATmega83
ATmega163 BOOT
ATmega83 BOOT
ATmega8535?? ATmega8535 BOOT??

* Verified device

- Use power supply from target board
- RS-232 control at 19200 BPS
- Support AVR Studio 4

Schematic detail

The schematic for AVR ISP show in picture 1, IC1 DS275 use for RS-232 Driver becuase it small and no need external component IC2 AT90S2313 is the CPU to communication and receive command from PC that run AVR Prog to control target CPU. The wire from AVR ISP to target CPU not exceed 15 cm

Schematic of AVR ISP

Component installation.

This firmware compiled to run on crystal 4MHz ,so the target device must connect crystal 4MHz on XTAL1 and XTAL2 pin.But, if your target device use internal oscillator and enabled .its not need any external oscillator.

To use this AVR ISP with target device that run at 8MHz you can do this by recompile the firmware source code. Before recompile you need to change the line in source code as below

.equ xtal_8mhz=0 ; if 0 then 4MHz Xtal

Change to :

.equ xtal_8mhz=1 ; if 0 then 4MHz Xtal

After change firmware you can compiler it by Avrasm found from ATMEL web site


To use AVR ISP
Picture show how to use AVR ISP

Download
- Source code
- Object code(Hex)
- schematic
- AVRProg


AVR ISP Programmer (In-Sytem programmer) for ATMEL


AVR ISP Programmer (In-Sytem programmer) for ATMEL


AVR ISP Programmer (In-Sytem programmer) for ATMEL

AVR ISP Programmer (In-Sytem programmer) for ATMEL





Accurate LC Meter Capacitance Inductance Meter with 16F628 and LCD
Volt Ampere Meter with 16F876 Microcontroller and LCD display
 
Accurate LC Meter

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging as well as reset switch and produces very accurate and stable readings.
PIC Volt Ampere Meter

Volt Ampere Meter measures voltage of 0-70V or 0-500V with 100mV resolution and current consumption 0-10A or more with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with 16x2 backlighted LCD.

50MHz 60MHz Frequency Meter / Counter with 16F628 & LCD
1Hz - 2MHz XR2206 Function Generator
60MHz Frequency Meter / Counter

Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.
1Hz - 2MHz XR2206 Function Generator

1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

BA1404 HI-FI Stereo FM Transmitter
USB IO Board PIC18F2455 / PIC18F2550
BA1404 HI-FI Stereo FM Transmitter

Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter broadcasts high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.
USB IO Board

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible.

ESR Meter / Transistor Tester Kit
Audiophile Headphone Amplifier Kit
 
ESR Meter / Capacitance / Inductance / Transistor Tester Kit

ESR Meter kit is an amazing multimeter that measures ESR values, capacitance (100pF - 20,000uF), inductance, resistance (0.1 Ohm - 20 MOhm), tests many different types of transistors such as NPN, PNP, FETs, MOSFETs, Thyristors, SCRs, Triacs and many types of diodes. It also analyzes transistor's characteristics such as voltage and gain. It is an irreplaceable tool for troubleshooting and repairing electronic equipment by determining performance and health of electrolytic capacitors. Unlike other ESR Meters that only measure ESR value this one measures capacitor's ESR value as well as its capacitance all at the same time.
Audiophile Headphone Amplifier Kit

Audiophile headphone amplifier kit includes high quality audio grade components such as Burr Brown OPA2134 opamp, ALPS volume control potentiometer, Ti TLE2426 rail splitter, Ultra-Low ESR 220uF/25V Panasonic FM filtering capacitors, High quality WIMA input and decoupling capacitors and Vishay Dale resistors. 8-DIP machined IC socket allows to swap OPA2134 with many other dual opamp chips such as OPA2132, OPA2227, OPA2228, dual OPA132, OPA627, etc. Headphone amplifier is small enough to fit in Altoids tin box, and thanks to low power consumption may be supplied from a single 9V battery.
 

Arduino Prototype Kit
RF Remote Control 433MHz Four Channel
 
Arduino Prototype Kit

Arduino Prototype is a spectacular development board fully compatible with Arduino Pro. It's breadboard compatible so it can be plugged into a breadboard for quick prototyping, and it has VCC & GND power pins available on both sides of PCB. It's small, power efficient, yet customizable through onboard 2 x 7 perfboard that can be used for connecting various sensors and connectors. Arduino Prototype uses all standard through-hole components for easy construction, two of which are hidden underneath IC socket. Board features 28-PIN DIP IC socket, user replaceable ATmega328 microcontroller flashed with Arduino bootloader, 16MHz crystal resonator and a reset switch. It has 14 digital input/output pins (0-13) of which 6 can be used as PWM outputs and 6 analog inputs (A0-A5). Arduino sketches are uploaded through any USB-Serial adapter connected to 6-PIN ICSP female header. Board is supplied by 2-5V voltage and may be powered by a battery such as Lithium Ion cell, two AA cells, external power supply or USB power adapter.
200m 4-Channel 433MHz Wireless RF Remote Control

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and can find many uses for controlling different devices, and it works even through the walls. You can control lights, fans, AC system, computer, printer, amplifier, robots, garage door, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of.
 

Electronics-DIY.com © 2002-2024. All Rights Reserved.