60MHz Frequency Meter / Counter
Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc.

 ESR Meter / Transistor Tester
ESR Meter / Transistor Tester is an irreplaceable tool for troubleshooting and repairing electronic equipment. It measures capacitor's capacitance and its ESR value. Tests and identifies PINs of Bipolar, FET and MOSFET transistors, Thyristors, SCRs and Triacs. Tests and identifies PINs and voltage of diodes, dual diodes, varicap diodes (and capacity), zener diodes (up to 5V) and LEDs. Measures resistance from just 0.1 Ohm up to 20 Mega Ohms.

 Voltmeter Ammeter
Voltmeter Ammeter can measure voltage with 100mV and current up to 10A with 10mA resolution. It is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored.

 Accurate LC Meter

Build your own LC Meter and start making your own coils and inductors. Accurate LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils. Accurate LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF.


 1Hz - 2MHz XR2206 Function Generator
1Hz - 2MHz XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output of 1Hz - 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output.

 USB IO Board
USB IO Board is a tiny spectacular little input / output development board featuring PIC18F2455 / PIC18F2550 microcontroller. When attached to a computer IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB IO Board is self-powered by USB port and can provide up to 500mA power for your projects. USB IO Board is breadboard compatible.

 Stereo FM Transmitter
High quality BA1404 Stereo FM Transmitter with crystal clear stereo sound, excellent frequency stability and good transmission range.

  Latest Electronic Kits & Components
Special Edition Accurate LC Meter Kit with Green Backlight LCD - FREE CASE
60MHz Frequency Meter / Counter Kit - Green Backlight LCD
1Hz - 2MHz XR2206 Function Generator Kit
Voltmeter Ammeter Kit
BA1404 HI-FI Stereo FM Transmitter - Special Edition Kit
USB IO Board Kit
ESR Meter / Transistor Tester Kit - Blue Backlight LCD
Serial I2C LCD Display Adapter
USB Male Connector Type A
Single-Sided PCB Copper Clad 3.5 x 5 (Can be cut with scissors)
ATMEGA168 Microcontroller
USB IO Board Kit
USB to RS232 TTL Adapter
SOIC8 SOP8 to DIP8 Adapter
4.7uF / 50V ELNA SILMIC II Audio Capacitor
DS18S20 Temperature Meter Kit - Blue Backlight LCD
DS18S20 Dual Temperature Meter Kit - Blue Backlight LCD
USB Battery Charger
Special Edition Accurate LC Meter Kit with Blue Backlight LCD - FREE CASE
PIR Motion Sensor Detector
USB AVR Programmer
SOT23 Adapter
Voltmeter Ammeter Kit - Blue Backlight LCD
Humidity Temperature Meter (Hygrometer)
60MHz Frequency Meter / Counter Kit - Blue Backlight LCD
Micro SD MP3 Player
4-Channel 433MHz Wireless RF Remote Control Kit (200m) - Momentary
USB Voltmeter Kit
USB Thermometer Kit with Data Logger
USB Relay Controller
Super Bright RGB LED (Common Anode)
Super Bright RGB LED (Common Cathode)
RGB LED Strip
Super Bright Clear White LED
Buzzer Alarm
220uF / 25V Nichicon MUSE Audio Series
10uF / 100V Nichicon MUSE Audio Series
18W TDA2030A Hi-Fi Stereo Audio Amplifier Kit
BA1404 HI-FI Stereo FM Transmitter - Special Edition Kit
ESR Meter / Transistor Tester Kit
Accurate USB 0-500MHz RF Power Meter Kit
PIC16F628 Microcontroller
PIC18F2550 Microcontroller Replacement
ATMEGA328 Microcontroller
10MHz Ceramic Resonator
16MHz Ceramic Resonator
12MHz Ceramic Resonator
6MHz Ceramic Resonator
8MHz Ceramic Resonator
24MHz Ceramic Resonator
20MHz Ceramic Resonator
Electret Microphone
RGB LED Candle (parts)
MCP9700 Temperature Sensor
24MHz Crystal
16MHz Crystal

 more electronic kits

 Gallery

 

BA1404 based transmitter is an exciting product that will broadcast high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPhone or a computer.

XR2206 Function Generator produces high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated. Output frequency can be adjusted from 1Hz up to 2MHz.

60MHz Frequency Meter / Counter measures frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding unknown frequency of oscillators, radio receivers, transmitters, function generators, crystals, etc. It has excellent input sensitivity thanks to onboard amplifier.



Build your own Special Edition Accurate LC Meter and start making custom made precision coils and inductors. Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. It can measure inductance starting from only 10nH - 1000nH, 1uH - 1000uH, 1mH up to 100mH and capacitance from 0.1pF up to 900nF. Accurate LC Meter is designed for professionals that require unprecedented measurement accuracy and includes high preci-sion components that are only found in premium quality kits.

Control appliances wirelessly with 4-Channel RF Remote Control. Works through the walls with 200m / 650ft range. You can control lights, fans, garage door, robots, security systems, motor-driven curtains, window blinds, door locks, sprinklers or anything else you can think of.



Voltmeter Amperemeter can measure voltage up to 70V with 100mV resolution and current up to 10A with 10mA resolution. It is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored. The meter uses PIC16F876A microcontroller with built-in ADC (Analog to Digital Converter) and 16x2 green backlighted LCD display. Circuit design uses very few components and may be mounted on a small PCB. The meter can also be modified and calibrated through three buttons to measure voltage higher than 70V and current greater than 10A.





























LM386 Utility Amplifier

Posted on Tuesday, July 01, 2014


It's always handy to have a little amp kicking around to trace audio signals, test mics, CD tape and TV audio outputs. You know, something that doesn't weigh a lot and isn't clumsy. There are tons of uses for this little circuit. There are a couple of versions of this amplifier chip. Both are 8 pin DIP packages and the difference between the two are apparent by their part numbers. Either are suited for this circuit provided the supply voltage does not exceed the recommended 5 to 12 volt DC range. Power output can range from about 325 mW to about 750 mW within this supply range when using an 8 ohm speaker. Power it with batteries or a small DC supply...why not solar cells or a little windmill generator?



Mini FM Transmitter

Posted on Friday, June 27, 2014


Here's how to build your own mini FM transmitter. It transmits FM waves so you could easily receive the signals on your mobile phone, radios, etc. As the name and the picture indicates it is very small and is approximately the size of a 9v battery clip. With this FM transmitter you could start your own mini FM station. The circuit uses BC547 transistor to amplify the signal and then frequency modulate it. It uses "frequency modulation" most commonly known as FM, the same principal to transmit audio signals captured by the microphone.



Automatic Garden Light

Posted on Sunday, June 22, 2014


This circuit automatically turns on and illuminates the LEDs when the solar panel does not detect any light. It switches off when the solar panel produces more than 1v and charges the battery when the panel produces more than 1.5v + 0.6v = 2.1v.



USB Battery Pack

Posted on Friday, June 20, 2014


This project is able to power a USB device using two standard AA batteries and an electronics circuit. The circuit is based on LT1073 DC/DC converter to convert the 3V to 5V needed by USB. In that way it can power the USB device on the go.



Phone Transmitter

Posted on Sunday, June 15, 2014


This small phone transmitter will transmit a phone conversation to an FM radio on the 88-108MHz band. It uses energy from the phone line to transmit the signal about 100 meters away. It uses the phone wire as the antenna and is activated when the phone is picked up. Transmitter components are mounted on a small PC board. PC layout is included.



27MHz Walkie Talkie

Posted on Friday, June 06, 2014


This classic walkie talkie consists of both 27MHz transmitter and receiver all in one circuit. Nearly all the components in the 4-transistor circuit are used for both transmitting and receiving making it simple to build and economical at the same time. The frequency-generating stage only needs 27MHz crystal to be removed and it becomes a receiver. Next is a three transistor audio amplifier with very high gain. The first transistor is a pre-amplifier and the next two are wired as a super-alpha pair, commonly called a Darlington pair to drive the speaker that is also used as a microphone. The use of telescopic antenna will provide better reception and transmitting range. Use two identical walkie talkie circuits for two way communication.



Plant Water Alarm

Posted on Sunday, June 01, 2014


This simple plant water alarm circuit indicates when the soil is dry and the plant needs watering. The circuit does not have a current-limiting resistor because the base resistor is very high and the current through the transistor is only 2mA. Replacing 220K resistor with 1M potentiometer will provide adjustment when the alarm should be triggered depending on the moisture left in the soil.



4km FM Transmitter

Posted on Friday, May 16, 2014


This is a VCO FM Transmitter. With good antenna (dipole placed outdoor and high) the transmitter has very good coverage range about 500 meters, the maximal coverage range is up to 4 km. To calibrate for maximum power connect 6 V / 0,1 light bulb to the output and use R1 to tune the right frequency, adjust L1 coil if necesary. Then use C14 and C15 to adjust the highest power (the highest light of the bulb). Then you can connect antenna and audio signal. Adjust R2 until the audio sounds as loud as the other stations.



1 Watt FM Transmitter Amplifier

Posted on Thursday, May 15, 2014


This is a 1 Watt FM Transmitter amplifier with a good design that can be used to amplify a RF signal in the 88 108 MHz band. It is very sensitive if you use good RF power amplifier transistors, trimmers and coils. It has a power amplification factor of 9 to 12 dB (9 to 15 times). At an input power of 0.1W the output will be 1W. You must choose T1 transistor depending on applied voltage. If you have a 12V power supply then use transistors like: 2N4427, KT920A, KT934A, KT904, BLX65, 2SC1970, BLY87. At 18 to 24V power supply you must use transistors like: 2N3866, 2N3553, KT922A, BLY91, BLX92A. You may use 2N2219 at 12V but you will get an output power of 0.4W maximum.



Simple MOSFET Switch

Posted on Tuesday, May 06, 2014


Constructing a MOSFET switch is one of the basic level electronics projects and could be useful for beginners to get a hang of the various FET transistors. The aim of this project is to make control a heavy duty DC load by constructing a simple switch. MOSFET transistors are capable of handling a large voltage and current. It is because of this feature that it is being much sought after for connecting heavy loads to a circuit or a microcontroller.



1Hz - 2MHz XR2206 Function Generator


Presented here is a premium quality 1Hz - 2MHz XR2206 Function Generator kit capable of producing high quality sine, square and triangle waveforms of high-stability and accuracy. The output waveforms can be both amplitude and frequency modulated.

Coarse frequency adjustment is accomplished using 4-DIP switch for the following four frequency ranges; (1) 1Hz-100Hz, (2) 100Hz-20KHz, (3) 20KHz-1MHz, (4) 150KHz-2MHz. Frequency output can be fine tuned using P1 and P2 potentiometers. The kit includes output that can be connected to 60MHz Counter kit to measure output frequency. 1Hz - 2MHz XR2206 Function Generator kit includes premium quality components, including Audio Grade Capacitors, Gold Plated RCA Connector, WIMA Capacitors, 1% Metal Film Resistors and premium quality PCB with red solder mask and plated through holes.




Special Edition Accurate LC Meter Kit

Special Edition Accurate LC Meter Kit
Build your own Special Edition Accurate LC Meter (Inductance Meter / Capacitance Meter) and start making custom made precision coils and inductors. Accurate LC Meter allows to measure incredibly small inductance making it perfect tool for making all types of RF coils and inductors. It can measure inductance starting from only 10nH - 1000nH, 1uH - 1000uH, 1mH up to 100mH and capacitance from 0.1pF up to 900nF.

Special Edition LC Meter includes top notch high precision components that are only found in premium quality kits. It includes high quality double-sided printed circuit board (PCB) with red solder mask and pre-soldered tracks for easier soldering, detachable LCD display with yellow-green LED backlight, programmed PIC16F628A microcontroller chip, high precision capacitors and inductor, 1% Metal Film resistors, Machined IC Sockets, gold plated header pins, LCD header connectors and all the other components that are needed to build a premium quality kit. Thanks to the use of LCD connectors LCD display can be detached from the main PCB board at any time even after the kit has been assembled. All components are through-hole and are easy to solder. Special Edition Accurate LC Meter is designed for professionals that require unprecedented measurement accuracy and offers great value at low cost.




10Hz - 60MHz Frequency Meter / Counter Kit

This is 60 MHz Frequency Meter / Counter for measuring frequency from 10 Hz to 60 MHz with 10 Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc. The meter provides very stable readings and has excellent input sensitivity thanks to onboard amplifier and TTL converter, so it can even measure weak signals from crystal oscillators. With the addition of prescaller it is possible to measure the frequency of 1GHz and above. The meter measuring range has been recently upgraded and it can now measure from 10Hz to 60MHz instead of 10Hz to 50MHz.




PIC Volt Ampere Meter



PIC Voltmeter Amperemeter can measure voltage 0-70V with 100mV resolution and current consumption 0-10A with 10mA resolution. The meter is a perfect addition to any power supply, battery chargers and other electronic projects where voltage and current must be monitored.


The meter uses PIC16F876A microcontroller with built-in ADC (Analog to Digital Converter) and 16 x 1 green backlighted LCD display. With slight modification it is possible to measure higher voltage and current.




BA1404 HI-FI Stereo FM Transmitter - Special Edition Kit

BA1404 HI-FI Stereo FM Transmitter Kit
Be "On Air" with your own radio station! BA1404 HI-FI Stereo FM Transmitter - Special Edition Kit is an exciting transmitter that will broadcast high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground. Add 500mW FM / VHF Transmitter Amplifier / Booster for even longer range.

Special Edition BA1404 HI-FI Stereo FM Transmitter Kit includes premium components with audio grade gold capacitors, 1% Metal Film Resistors and quality PCB with Red Solder Mask and Plated-Through Holes. The kit is based on the popular BA1404 stereo broadcaster IC which contains all the complex circuitry for generating the stereo FM signal. 38 KHz crystal provides a rock solid stability of sub-carrier for stereo signal.




USB IO Board with PIC18F2455/PIC18F2550 Microcontroller

USB IO Board PIC18F2455/PIC18F2550

USB IO Board is a tiny spectacular little development board / parallel port replacement featuring PIC18F2455/PIC18F2550 microcontroller. USB IO Board is compatible with Windows / Mac OSX / Linux computers. When attached to Windows IO board will show up as RS232 COM port. You can control 16 individual microcontroller I/O pins by sending simple serial commands. USB Input / Output Board is self-powered by USB port and can provide up to 500mA for electronic projects. USB IO Board is breadboard compatible. Simply solder included 12-PIN & 8-PIN male headers on the bottom side of the PCB and the board can be plugged into a breadboard for quick prototyping.

USB IO Board PIC18F2455/PIC18F2550

These are examples of what can be built using USB IO Board:
USB Relay Controller (turn ON/OFF lights or appliances in the house).
Control LEDs, toys, electronic gadgets, wireless control, etc.
USB LCD Controller
USB Volt / Ampere / Wattage Meter. USB CNC Controller
USB Data Logger
USB Temperature Meter / Logger
USB Thermostat
USB Humidity Meter / Logger
USB Digital RF Power Meter
USB Stepper Motor Controller
USB RC Servo Controller
and much more




5W PLL Stereo FM Transmitter


5W PLL Stereo FM Transmitter features PLL synthesized drift free operation with high quality BH1415 chip. 5W RF output power is achieved with 2SC1971 6W transistor in the output stage. Front panel digital control comes with LED display and case is made high quality aluminum. The board features EMI filtering on audio and power inputs and comes with Microphone and Audio inputs. Once transmitter is turned on it starts broadcasting with previously selected frequency. Overall this 5W PLL Stereo FM Transmitter provides professional broadcast audio quality and rivals commercial broadcasts.




500mW FM / VHF Transmitter Amplifier / Booster

This is a high performance low noise 500mW amplifier / booster for all low power FM transmitters such as BA1404, BH1417, BH1415, 433MHz transmitter modules, etc. The amplifier chip is an integrated circuit containing multiple transistor stages and all other parts conveniently within a single small package. Boosting your FM transmitter has never been easier and the output signal can also directly drive 2n4427 or 2n3886 transistors for 1W or 5W of RF output power.

SPECIFICATIONS
- Output Power: 500mW
- Input Frequency: 50MHz - 1300MHz
- Voltage Supply: 9-12V




Phone FM Transmitter


This Phone FM transmitter connects in series to your telephone line and transmits the telephone conversation over the FM band when you pick up the telephone handset. Transmitted signal can be tuned by any FM receiver. The circuit includes an "On Air" LED indicator and also provides a switch which can be used to turn off the transmitter. A unique feature of the circuit is that no battery is needed to operate the circuit since power is taken from the telephone line.




Special Edition Accurate LC Meter Kit with Green Backlight LCD


Build your own LC Meter and start making custom made coils and inductors. This LC Meter allows to measure incredibly small inductance making it perfect tool for making all types of RF coils and inductors. LC Meter can measure inductance starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitance from 0.1pF up to 900nF. The circuit includes an auto ranging and reset switch to make sure the readings are as accurate as possible.


This is a Special Edition LC Meter with upgraded top notch components. It includes upgraded high precision capacitors, inductor, 1% Metal Film resistors and Gold Plated Machined IC Sockets, header pins and LCD header connectors. This edition is designed for professionals that require unprecedented measurement accuracy.




USB Relay Controller


This is a new project USB Relay Controller that allows to control from eight to fifteen external devices through computer's USB port. You may control different appliances in your house such as lights, fans, garden sprinklers, computers, printers, TV sets, radios, music systems, air conditioners, fish tanks, or anything else you can think off, all conveniently through your computer. The software features iPhone based interface and it is fun to work with.
Stay tuned for more details ...




BA1404 HI-FI Stereo FM Transmitter Kit


Be "On Air" with your own radio station! BA1404 based transmitter is an exciting product that will broadcast high quality stereo signal in 88MHz - 108MHz FM band. It can be connected to any type of stereo audio source such as iPod, Computer, Laptop, CD Player, Walkman, Television, Satellite Receiver, Tape Deck or other stereo system to transmit stereo sound with excellent clarity throughout your home, office, yard or camp ground.


The circuit is based on the popular BA1404 stereo broadcaster IC which contains all the complex circuitry for generating the stereo FM signal. 38 KHz crystal provides a stable sub-carrier for the stereo signal. The oscillator circuit is stable enough for reliable reception even on digitally tuned FM radios. PCB includes green solder mask layer for easier soldering and protects wires that do not need soldering.




Accurate LC Meter Kit





Build your own LC Meter and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils. LC Meter can measure inductances starting from 10nH - 1000nH, 1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up to 900nF. The circuit includes an auto ranging and "Zero Out" function to make sure the readings are as accurate as possible ...




DS18S20 Dual Temperature Meter

DS18S20 Dual Temperature Meter

This is extremely simple to build PIC Temperature meter that allows to measure temperature in two different locations at the same time. Meter can display both Celsius and Fahrenheit values (together or individually) and is capable of measuring temperatures from -55 to 125 degrees Celsius (-67 to 257 degrees Fahrenheit). Never before such a useful and powerful circuit could be built with so little components and yet provide endless possibilities. This is all possible thanks to the use of PIC16F628 microcontroller and 2x16 character LCD display that act like a small computer which can be customizable thanks to upgradeable hex firmware.

Presented PIC temperature meter uses two very exciting DS18S20 1-Wire digital temperature sensors. Unlike regular sensors where temperature readings are passed as varying voltage, DS18S20 passes temperature information in a digital format as data. This brings many new possibilities and enables to pass temperature information over much longer distances just over a two wire cable.




4-Channel Remote Control System with Four Relays


Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m and can find many uses for controlling different devices around the house.

4 button RF remote is used to turn ON / OFF 4 different devices independently. 10A Relay outputs can switch appliances that use 110V / 220V mains voltage.




RF Amplifier Remote Volume Control with Power Control, Input Source Selection and Speaker Protection

This is very simple yet unique RF Amplifier Remote Volume Control based on PIC16F628 microcontroller that offers features that other remote volume controls do not.



1) Long Range Wireless 433MHz RF Radio Remote Control allows to control amplifier even through the walls
2) Allows to control audio volume with high quality Motorized ALPS Stereo Potentiometer
3) Allows to turn ON / OFF Audio Amplifier
4) Automatically turns ON speakers 2 seconds after the power has been turned ON to eliminate the power-on noise
5) Automatically turns Speakers OFF 1/2 second before power is disconnected to eliminate the power-off noise
6) Allows to switch input between two audio sources



More information will be available soon ...




PIC Temperature Meter with Thermostat and Backlighted LCD



This is our upcoming project that is similar to PIC Dual Temperature Meter but with the thermostat option built-in. Besides displaying customized temperature readings in Celsius and/or Fahrenheit degrees it will turn on heater if the temperature drops below specified temperature or it can be set to turn on the fan or air conditioning system if the temperature reaches above specified temperature that is set by UP / DOWN buttons. Thermostat can display both Celsius and Fahrenheit values (together or individually) and is capable of measuring temperatures from -55 to 125 degrees Celsius (-67 to 257 degrees Fahrenheit)


Presented PIC temperature meter with thermostat uses very exciting DS1820 1-Wire digital temperature sensor. Unlike regular sensors where temperature readings are passed as varying voltage, DS1820 passes temperature information in a digital format as data. This brings many new possibilities and enables to pass temperature information over much longer distances just over a two wire cable.

Stay tuned for full details on this project.




RF Remote Control with Four Independent ON / OFF Relay Outputs

This is a new project that uses four button RF remote control to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either momentary or ON / OFF mode. Outputs are buffered by BC549 transistors and can drive devices directly or be connected to 5V / 12V Relays to turn ON / OFF appliances that use higher 110V / 220V voltage.



Remote control provides long range of up to 200m / 650ft and can find many uses for controlling different indoor and outdoor devices. We will be providing all components for building this project. Stay tuned for more information.







24-Bit 192KHz PCM1793 Audio DAC



24-Bit 192KHz PCM1793 DAC is perfect solution for upgrading audio components such as CD Player, DVD Player, Blue Ray Player, Computer, and Satellite receiver. It can be easily connected via Coaxial S/PDIF or Optical Cable and provides convenient analog output connectors. PCM1793 Audio DAC board features advanced Burr-Brown PCM1793 DAC chip, high quality OPA2134 op-amp, and latest DIR9001 digital line receiver. PCB board is built with high quality components such as Nichicon Audio capacitors, WIMA capacitors, gold plated connectors, gold plated PCB tracks and metal film resistors. PCM1793 DAC provides detailed heights and exceptionally good sound stage.




A4 Power Amplifier


As the stunningly original name suggests, the A4 contains 4 separate power amplifiers. This unit offers great flexibility - the following modes of operation are available: * Four-channel 50 watts per channel operation for surround-sound or multi-room operation. * Two-channel bi-amped mode, for suitably bi-wireable loudspeakers. * Two channel Bridged mode, offering around 150 watts per channel.




8W PLL Stereo FM Transmitter with LCD


Very stable FM transmitter based on TSA5511 synthesizer. Frequency is performed with three buttons through PIC16F84 microcontroller. Frequency is displayed on 16x1 LCD.




LM3886 Power Amp with DIY Chassis


This is a simple chassis using just 4 aluminum panels and 2 heatsinks. Designed around dimensions to tightly pack in a LM3886 chip amp kit.


The top and bottom panels sit in ridges cut into the heatsinks with a table saw, and then the front and back panels just bolt into the end fins. Rear panel fixings are held with M3 nut and bolts, and panels that join to the heatsinks are held by M4 bolts tapped directly into the heatsinks so no additional brackets are required. Heatsinks are 75 x 160 x 50mm with a 10mm thick base.




100W HiFi MOSFET Amplifier


This is a high fidelity 100W MOSFET Amplifier. The benefits of using MOSFETs in the output stage is that they have a high input impedance at low frequencies, and are capable of extremely high slew-rates. This very attribute makes them rather prone to HF oscillation when improperly compensated, but with careful design they're capable of delivering an impressive performance.




Dual Channel 70V PIC Voltmeter

This is a sneak preview of upcoming PIC voltmeter project. You may use this PIC voltmeter for your power supply, as a battery meter for car, RC cars, RC helicopters, to monitor voltages in your computer or it could be used as a small portable voltmeter.

PIC voltmeter can measure 0-70 Volts which should be more than enough for most of electronic projects providing excellent reading accuracy and resolution. It has two input channels for measuring two voltage sources at the same time. This PIC voltmeter project uses PIC16F876 microcontroller with built-in ADC (Analog to Digital Converter) and 2x16 backlighted LCD display. Circuit design uses very few components and may be mounted on a small PCB. Stay tuned for more info.




AVR Programmer



This simple AVR Programmer will allow you to painlessly transfer hex program to most ATMEL AVR microcontrollers without sacrificing your budget and time. It is more reliable than most other simple AVR programmers available out there and can be built in very short amount of time.

Entire AVR programmer has been build with using very simple parts and easily fits in the case of the serial connector. The socket pcb has been created to to fit a 28-DIP AVR Atmega8 microcontroller, but you can easily build a socket pcb for any other AVR microcontroller. This AVR programmer is compatible with a popular PonyProg that even shows you a status bar of the programming progress.




Upcoming PIC Voltmeter Project

Soon we will post a PIC Voltmeter project with 2x16 LCD display that can measure dc voltage from 0 to 70V. PIC Voltmeter is using PIC16F876 microcontroller that features built-in analog to digital converter (ADC) and uses very few external components. Voltage readings are very accurate and this microcontroller based meter is a perfect addition to your laboratory power supply.




BH1417 PLL Stereo FM Transmitter



This is a high quality PLL Stereo FM Transmitter with build-in VHF amplifier with impressive transmission range. It is based on BH1417 chip that offers high quality crystal clear stereo transmission. Eight available frequencies are controlled by grounding 3 pins on header connector. This transmitter comes assembled and is ready to use.




Single chip USB MP3 Player



This MP3 player module is based on the latest innovative BU9432 chip from RHOM. It features USB 1.1 / 2.0 Controller, MP3 decoder, system controller for loading MP3 files form a USB flash drive, USB hard drive, USB CD-ROM or USB DVD-ROM drive all in one chip.

Once USB flash drive is connected, BU9432 automatically searches for MP3 files for playback. Audio is controlled by tactile buttons; Play, Stop, Previous Song and Next Song.

BU9432 can decode VBR MP3, MP2, MP1, Layer 1, 2, 3 files with Sampling rate: 8K - 48KHz and Bit rate: 8Kbps - 448Kbps. It can also recognize FAT16 and FAT32 USB flash drive / hard drive with capacity from 32MB to 2TBytes. Audio playback is exceptionally good with 93dB signal to noise ratio and 88dB dynamic range.




BA1404 - HI-FI Stereo FM Transmitter Project


This high quality stereo FM transmitter prototype is a result of many hours of testing and tweaking. The goal was simple; to test many existing BA1404 transmitter designs, compare their performance, identify weaknesses and come up with a new BA1404 transmitter design that improves sound quality, has very good frequency stability, maximizes transmitter's range, and is fairly simple for everyone to build. We are happy to announce that this goal and expectations have been met and even exceeded.


The transmitter can work from a single 1.5V cell battery and provide excellent crystal clear stereo sound. It can also be supplied from two 1.5V battery cells to provide the maximum range.




SAA1057 PLL Frequency Synthesizer IC in Stock

We have just received a new batch of hard to find SAA1057 ICs. SAA1057 is a popular integrated circuit that is used as PLL Frequency Synthesizer in AM / FM transmitters.




ELNA SILMIC II Audio Aluminum Capacitors Now Available


The SILMIC II series are Elna's highest grade audio aluminum electrolytic capacitors that exhibit superior acoustic characteristics. An entirely new type of electrolytic separating paper is used, containing silk fibers. The extreme softness of silk can mitigate vibrational energy (generated by the electrodes, by external vibrations and by electromagnetic fields). Due to it's new electrolytic and foil design the signal propagation speed has increased (the ESR is reduced) and a more powerful, yet-mellow, sound is possible than before. When these capacitors were subjected to aural evaluations, the high range peak and midrange roughness were reduced substantially. Also, the low range richness and power were increased in the obtained high-quality sound.




BH1415 HI FI Stereo Encoder with Limiter and Low Pass Filter

This is the latest BH1415 Stereo Encoder design from RHOM that includes a lot of great features in one small package. It comes with pre-emphasis, limiter so that the music can be transmitted at the same audio level, low pass filter that blocks any audio signals above 15KHz to prevent any RF interference and crystal based stereo encoder for stereo transmission.




BH1417 HI FI Stereo Encoder with Limiter and Low Pass Filter

This is the latest BH1417 Stereo Encoder design from RHOM that includes a lot of great features in one small package. It comes with pre-emphasis, limiter so that the music can be transmitted at the same audio level, low pass filter that blocks any audio signals above 15KHz to prevent any RF interference and crystal based stereo encoder for stereo transmission.




TDA7000 FM Receiver / TV Tuner / Aircraft Receiver

This simple one chip FM receiver / TV tuner will allow you to receive frequencies from 70 up to 120MHz. With this small receiver it is possible to pick up TV stations, entire 88 - 108MHz FM band, aircraft conversation and many other private transmissions. It is a perfect companion to any FM Transmitter especially if FM band in your area is very crowded. TDA7000 receiver offers very good sensitivity therefore it will even allow you to pickup weaker signals that cannot be heard on conventional FM receivers.

A neat feature of presented TDA7000 FM receiver is a voltage controlled oscillator similar to TV tuners that are used in television sets ...




Microcontroller Voltmeter / Ammeter with LCD


This multimeter was designed to measure output voltage 0-30V and current with 10mA resolution in a Power Supply, where the current sense shunt resistor is connected in series with load at the negative voltage rail. It needs only one supply voltage that can be acquired from main PSU. An additional function of the multimeter is that it can control (switch on and off) an electric fan used to cool the main heatsink. The power threshold at which the fan switches on can be adjusted using One Touch Button Setup.




PCM2706 High Fidelity USB Soundcard / USB Headphones


This is a high fidelity external USB Soundcard / USB Headphones project that can be built for your PC or Mac. It is based on the latest PCM2706 IC which functions as a high quality, crystal clear 16-BIT Stereo DAC. It is a single chip digital-to-analog converter that offers two D/A output stereo channels, digital S/PDIF output and requires very few external components. PCM2706 includes integrated USB 1.0 & USB 2.0 compliant interface controller and it is conveniently powered directly from USB connection. PCM2706 is a USB plug-and-play device and does not require any driver installation under Windows XP and Mac OSX.




BH1417 Stereo PLL FM Transmitter


This is the latest BH1417 FM Transmitter design from RHOM that includes a lot of features in one small package. It comes with pre-emphasis, limiter so that the music can be transmitted at the same audio level, stereo encoder for stereo transmission, low pass filter that blocks any audio signals above 15KHz to prevent any RF interference, PLL circuit that provides rock solid frequency transmission which means no more frequency drift, FM oscillator and RF output buffer.




LCD Controllel Project


This is our upcoming project where you will learn how to use your computer's parallel port to send text messages to two line 16 character LCD display. Once you will build PC to LCD interface which only requires a parallel port connector, cable and an LCD, you can set your imagination free and build a lot of interesting projects like car MP3 player, display date and time, weather information, and much more.




Parallel Port Controller Project


This is a very easy and fun to build project that will allow you to control up to eight external devices through your computer's parallel port. You may for instance control different appliances such as lamps, computers, printers, tv sets, radios, music systems, air conditioners, air fans, garden sprinklers and anything else you can think of, all through your computer.

In the future versions you will be able to program at what time a particular device should be turned on or off. If you should have any suggestions for any additional features please let us know.




ICL7107 - DIGITAL LED VOLTMETER

This digital voltmeter is ideal to use for measuring the output voltage of your DC power supply. It includes a 3.5 Digit LED display with a negative voltage indicator. It measures DC voltages from 0.1 to 199.9V with a resolution of 0.1V. The voltmeter is based on single ICL7107 chip and may be fitted on a small 3cm x 7cm printed circuit board. The circuit should be supplied with a 5V voltage supply and consumes only around 25mA.




ICL7107 - DIGITAL LED AMPERE METER

Ammeter is a great addition to any Laboratory Power Supply as it will allow you measure the current consumption and help determine if there are any problems with the circuit that you are building or testing. This amper meter is capable of measuring the current consumption from 1mA up to 10A with selected 1mA, 10mA and 100mA resolutions, and consumes only about 25mA of current.

The ammeter is based on single ICL7107 chip and 3.5 Digit seven segment LED display. Due to a relatively small number of components that the circuit is using it is possible to fit it on a small 3cm x 7cm printed circuit board.




New TX200 transmitter with optional PLL and stereo encoder



Here is the latest and greatly improved TX200 VFO/VCO FM transmitter. The most versatile transmitter to date that can be turned into high fidelity stereo PLL based 200mW FM transmitter. It is a perfect circuit for transmitting your music around the house and yard. TX200 uses only two coils; one in the oscillator and the other one in the 200mW VHF amplifier so it should be fairly easy for anyone to build.




Varicaps (Tuning Diodes)

New replacements for hard to find varicap diodes. These variable capacitance diodes change its capacitance as voltage is applied to them. They are perfect for tuning the frequency of PLL based FM transmitters, VCO FM Transmitters, FM / VHF receivers, TV tuners, etc.

MV2105 - 2-16pF varicap diode replacement for BB105 and BB205 varicap diodes.

MV2109 - 2-36pF varicap diode replacement for BB109, BB209 and BB405 varicap diodes.

MV104 - 2-42pF DUAL varicap diode replacement for KV1310, BB104, BB204 and BB304 varicap diodes.

Please refer to TX200 FM transmitter page to see examples on how you can implement varicap diodes in your own projects http://electronics-diy.com/tx200.php




Very Accurate LC METER based on PIC16F84A IC


Finding a "good" LC Meter (inductance / capacitance meter) that would accurately measure all inductor types and coils is not an easy task. We have been searching for this type of LC meter for a long time now. We have been considering many commercial LC meter versions, but most of them were either too pricey or limited in measurement ranges.

Finally, after studying different PIC16F84 based LC meter designs, a lot of testing and tweaking, we have came up with a unique design. The LC Meter is very compact and fairly simple to build. It's based on the PIC16F84A, LM311 ICs, and LCD module.




The heart of the meter is a PIC16F84A IC that performs LC calculations, and LM311 IC that functions as a frequency generator. The LC Meter can measure surprisingly small inductances; starting from 10nH, whole uH range and mH up to 100mH. It also measures capacitances starting from 0.1pF up to 900nF.




Tunable RF Coils


We will soon carry the following tunable RF coils that are perfect for precise frequency tuning of your transmitter. The magnet wire is halfway embedded within the plastic, providing excellent frequency stability. One of these coils have been tested in the TX200 transmitter as a substitution for an air coil and a variable capacitor. As a result the frequency stability was greatly improved. The coils are 7mm x 10mm and each comes with its own metal can, which may be removed. Tunable RF coils come in the following inductance ranges:

2.5 turns 48 - 59nH (Red)
3.5 turns 65 - 79nH (Orange)
4.5 turns 90 - 109nH (Yellow)
5.5 turns 109 - 132nH (Green)




BA1404 Stereo FM Transmitter IC in stock

As of today we are starting the sale of the popular BA1404 IC which has integrated stereo encoder and FM transmitter, all in one package. We also carry 38KHz crystals so if you have been waiting to build your own stereo FM transmitter to transmit your music around the house, grab a schematic from the "Schematics" section and start building one today.




Designing your own Printed Circuit Boards

Designing your own PCBs is a huge convenience, and you can create a professionally looking PCB in a manner of hours, depending on the size and complexity of the project.

Electronics-lab has posted a nice article that shows you a step-by-step procedure on how to use Eagle Layout Editor <http://www.cadsoft.de/download.htm> to create a PCB design as well as Adobe Photoshop which you may use to create final touches and print it.




PLL Module for your FM Transmitter



For a fraction of price of the PLL transmitter kit you can build this small PLL module that will allow you to upgrade your existing FM transmitter to be; fully digitally tuned and to have rock solid frequency stability. The circuit is based on SAA1057 Philips frequency synthesizer, PIC16F84A microcontroller from PICMicro and 4MHz crystal.

The PLL module works amazingly well and connection to the FM transmitter is very easy. In fact it requires only four components; two varicap diodes, 100K resistor and 1-10pF capacitor. I will post a tutorial on how to connect this PLL module to the TX200 transmitter once I find some more time.




Testing and using Varicap Diodes in VCO oscillators

Here is another small tutorial on how you can test and use varicap diodes in the voltage controlled or PLL based FM oscillators.




Digital Voltmeter with 3.5 LCD Display


Build an inexpressive 0.1 - 199.9V LCD digital voltmeter that can be easily configured as amper and temperature meter. This module is based on a popular ICL7106 IC that can measure its own voltage supply and offers very low power consumption.




High quality PIC programmer


This is the most attractive USB PIC Programmer that has great features in a compact design. It comes with a 40-pin ZIF (zero insertion force) socket, upgradeable firmware on PIC16F628 chip, ICSP (In Circuit Serial Programming), easy to use GUI software, and can program wide range of PICMicro microcontrollers.




Control stepper motor through your computer's parallel port

Build an easy stepper motor driver that will allow you to precisely control a unipolar stepper motor through your computer's parallel port.

The project comes with a program that has easy to use graphical interface, allows you to control the motor speed, direction in real-time and it also allows you to use and learn about different stepping methods, such as single stepping, high torque stepping and half stepping modes.

Stepper motor controller also displays an animation that helps you visualize the current as it flows through individual coils. It is a wonderful tool to learn how stepper motors work.




New TX200 Transmitter



This is our newest TX200 transmitter. It is a highly improved addition to our TX500 and TX300 transmitter family. TX200 is a 200mW FM Transmitter that offers excellent frequency stability and improved sound quality.



It features an oscillator that is based on BF199 low noise transistor and high precision adjustable coil. TX200 also includes a BF199 based VHF amplifier that eliminates frequency drifts and boosts the strength of the RF signal to 200mW. In addition to that TX200 has also built in LED based RF meter that indicates the strength of the transmitted RF signal. The transmitter can be supplied with 6 to 12V and offers low power consumption. It can be used as a stand alone transmitter or connected to an external VHF power amplifier to achieve an even greater transmission range. When connected our stereo encoder kit, TX200 is converted into an affordable high fidelity stereo FM transmitter.




HI-FI NJM2035 Stereo Encoder

This stereo encoder is the perfect for those looking for a high quality stereo sound transmission at a low cost. This stereo encoder produces an excellent crystal clear stereo sound and very good channel separation that can match with many more expensive stereo encoders available on the market. This is all possible thanks to NJM2035 chip and 38KHz quartz crystal that controls the 19kHz pilot tone. You will never have to calibrate or re-adjust the circuit's frequency.





Electronics-DIY.com © 2002-2013. All Rights Reserved.


 
 DTMF Decoder with LCD Display

The DTMF decoder 2 is a useful tool used for decoding DTMF (Dual Tone Multi frequency) generated by telephones. The decoded digits are viewed on a 16x2 LCD screen.

 Temperature Control using a DS1621 Sensor and a ATtiny 2313 Micrcontroller

This circuit uses a Dallas DS1621 temperature sensor which indicates the temperature of the device. The temperature sensor has an thermal alarm output, which becomes high when the temperature of the device exceeds a user defined value. When the temperature drops below a user defined value, the alarm output becomes low. In this way any amount of hysteresis can be programmed. The values are stored in a special register of the device that is nonvolatile. The signal of the alarm ...

 Stereo Limiter

Stereo Broadcast Limiter Circuit for Ramsey.

 Stereo Tone Control Circuit with Adjustable Bass-Treble

PCB Tone control adjustable bass-treble Stereo by IC LM348

 Lead Acid Battery Charger Circuit

Here is a lead acid battery charger circuit using IC LM317.The IC here provides the correct charging voltage for the battery. A battery must be charged with 1/10 its Ah value. This charging circuit is designed based on this fact.The charging current for the battery is controlled by Q1,R1,R4 and R5. Potentiometer R5 can be used to set the charging current. As the battery gets charged the the current through R1 increases.

 Count Down Timer

Timer kits are an ever popular item with the hobbyist. One of the main methods used is the ever-popular 555 timer IC. In this circuit we use a 555, a counter IC and a transistor switch to activate a relay either on-to-off or off-to-on (mode selected by a jumper) as soon as the counting period is over. Let us look at the kit in more detail. The circuit consists of 3 parts: an oscillator, a ripple counter and two switching transistors.

 500W 12V to 220V Inverter

This is a 500W DC-to-AC inverter circuit diagram which produces an AC output at line frequency and voltage. 12VDC to 220V 50Hz inverter circuit will power 220V or 110V appliances from 12V car battery. The circuit is easy to make and is low cost. Use proper transformer. The output (in watts) is up to you by selecting different power rating transformer and power transistor rating. If you load electronic device which require 120V AC, then use transformer with 120V in ...

 HA1377 Bridge Amplifier BCL cap 17W (Car audio)

This is circuit Car audio Amplifier(Bridge Amplifier BCL) , It use IC HA1377, Supply Volt 12V-13V. Speaker 4 OHM. Nice Circuit and Easy to Build.

  BH1417 PLL Stereo Transmitter

This is the latest BH1417 FM Transmitter design from RHOM that includes a lot of features in one small package. It comes with pre-emphasis, limiter, stereo encoder, low pass filter, PLL rock solid frequency transmission and RF output buffer.

 Big Ear Amplifier

This circuit, connected to 32 Ohm impedance mini-earphones, can detect very remote sounds. Useful for theatre, cinema and lecture goers: every word will be clearly heard. You can also listen to your television set at a very low volume, avoiding to bother relatives and neighbors. Even if you have a faultless hearing, you may discover unexpected sounds using this device: a remote bird twittering will seem very close to you. Ear amplifier is powered by 1.5V battery and draws only 7.5mA ...

 Portable FM Transmitter

This portable FM Transmitter is easy to build. I have used a pair of BC548 transistors in this circuit. Although not strictly RF transistors, they still give good range. Transmitter is powered by 9V battery. The coil L1 consists of 7 turns on a quarter inch plastic former with a tuning slug. The tuning slug is adjusted to tune the transmitter. Actual range on my prototype tuned from 70MHz to around 120MHz. The aerial is a few inches of wire. ...

  10Hz - 60MHz Frequency Meter / Counter

This is 60MHz Frequency Meter / Counter for measuring frequency from 10Hz to 60MHz with 10Hz resolution. It is a very useful bench test equipment for testing and finding out the frequency of various devices with unknown frequency such as oscillators, radio receivers, transmitters, function generators, crystals, etc. The meter provides very stable readings and has excellent input sensitivity thanks to onboard amplifier and TTL converter, so it can even measure weak signals from crystal oscillators. With the addition of ...

 Publish Your Circuit
Would you like to have your circuit published on electronics-diy.com?

Make it available to the world now. All credits will be yours and we will list your name, e-mail address and your website URL if you have one.


Submit Project

 Feedback
Let us know how we can better serve you or what electronic projects or kits you would you like to see at Electronics-DIY.