HOME     STORE     BLOG     SCHEMATICS     TUTORIALS     DOWNLOADS     CONTACT

Having the ability to control various appliances inside or outside of your house wirelessly is a huge convenience, and can make your life much easier and fun. RF remote control provides long range of up to 200m / 650ft and it works even through the walls. You can control many low voltage gadgets including motors, RC cars, robotic devices, amplifiers or 110V/220V appliances through relays such as lights, fans, AC systems, home appliances, garage doors, security systems, motor-driven curtains, motorized window blinds, door locks, sprinklers, motorized projection screens and anything else you can think of. 4-CH RF remote control is used to turn ON / OFF four different devices independently. Any of the four outputs can be configured to work independently in either toggle or momentary mode. Outputs are buffered by BC549 NPN transistors and can drive low voltage devices directly such us motors or be connected to either 5V or 12V relays to control appliances that use 110V / 220V mains voltage or any voltage of your choice. Multiple remote systems can be used independently to control more than four appliances in the same location by changing the address code on 433MHz receiver and remote. It is also possible to use several remotes to control the same appliance such as garage door.

How many times you needed some remote control to handle some electric device ? many times. There are lot of remote controls like infrared, RF, SMS (like my other circuit) and more. The basic small-range remote controls are 2, Infrared and RF (Radio Frequency). One of the weaks of Infrared is that the signal can not pass the walls. So, if you want to control your garage door, the only way is to use some RF remote control. The circuit (transmitter and receiver) use few components and ordinary (I love few component circuits) . Its easy to build it because you don't have to tune-up any coil or variable capacitor. The RF modules are fix to work in 418MHz area.

On these pages, I will introduce Remote Controller with Radio Frequency. The electric wave sending-out is controlled with the code by PIC for transmission and the code is deciphered by PIC for receiving.

This project is a 2 channel infrared (IR) remote controlled relay driver with power saving. It works with 12-bit SIRC IR signals as used by Sony remote controls. The board uses Microchip's low cost PIC10F200 microcontroller along with a handful of easy to find components making this possibly the lowest cost remote controlled relay driver around.

This project is a 3-channel IR remote control with 3 output relay and easy to build. Features: CPU PIC12F629 at 4MHz crystal for Tx/Rx, 3 channel output relay, The Tx use sleep mode for saving battery power, Use Phillips RC5 protocol, distance more than 7 m, Easy circuit to build and assembly and small amount of components. Uses RC5 protocol which is probably the most used by hobbyists, probably because the wide availability of cheap remote controls and easy to understand.

This is a 3 channel RF remote control project.The transmitter powered by 3V battery(coin size) range about 10 m. This remote control I use PIC12F509 from Microchip which is a 8-pin single-chip microcontroller designed for low pin count applications with 1 K words flash memory and 41Byte SRAM and some special features such Power-saving Sleep mode,Wake-up from Sleep on pin change.

This IR remote control that you can use to control other devices or circuits up to 8 devices. The control codes are sent in RC5 format modulated to about 38 kHz carrier frequency.The IR transmitter powered by the CR2016 which is a 3V button Cells Battery CR2016. To extend the life of the battery this is done by putting the CPU into SLEEP mode for most of the time and wake-up only when a key is pressed.

This IR remote control that you can use to control other devices or circuits up to 8 devices. The control codes are sent in RC5 format modulated to about 38 kHz carrier frequency.The IR transmitter powered by the CR2016 which is a 3V button Cells Battery CR2016.To extend the life of the battery this is done by putting the CPU into SLEEP mode for most of the time and wake-up only when a key is pressed. PIC16F630 is the heart of the transmitter used to send IR command to receiver.It also generate 38KHz carrier frequency.The CR2016 is 3V battery which is supply for the circuit. When any key not pressed the CPU work in SLEEP mode to reduce baterry power consumption and wake-up only when any key pressed. To wake-up the CPU from SLEEP mode the CPU use interrupt on change feature which interrupted when the state on PORTA change then the program execution after an interrupt is at the interrupt vector, if the global interrupt is not enabled, the program starts executing the first line of code right after the SLEEP instruction.In the interrupt service routine the software will scan the key that pressed and send IR command appropriate with key pressed.

This is an 8 Channel RF Remote Transmitter and Receiver that will allow to remotely control various electronic projects. RF Remote Control provides 2 latched and 6 momentary outputs that could be used to control your favorite devices such as amplifier, robotic devices, RC cars, computer, home appliances, lamps and many other cool gadgets.

This is a 8 channel RF remote control project. The transmitter powered by 5V.the RF module I used had long start-up and power down period after receiving a high pulse. To counter all of this I kept the receiver in constant standby mode, but sending a information all the time. That way the noise is flooded out, and the receiver will always respond. I had been trying all sorts of error detection methods and different ways of encoding the bytes, when I just gave up. Since the link is so noisy I decided to cut out all of the error detection methods and just make it accept anything it receives, and see what happened from there. But what do you know, it worked!