HOME     STORE     BLOG     SCHEMATICS     TUTORIALS     DOWNLOADS     CONTACT

This is circuit Car audio Amplifier(Bridge Amplifier BCL) , It use IC HA1377, Supply Volt 12V-13V. Speaker 4 OHM. Nice Circuit and Easy to Build.

After the euphoria over receiving my new Sony Minidisc bundle had partially subsided, I noticed that the portable unit, the MZ-E40, has a rather weak output. Measurements showed that it can only manage 80mV rms output and only about 74dB SPL output from the phones. This is when recording at average level with 8dB of headroom. In contrast, an orchestra can deliver more than 95dB SPL and they aren't considered headbangers. I tried all sorts of solutions, but in the end realized that the only solution yielding the headroom and quality worthy of the marvelous minidisc is to build a headphone amp from scratch.

Can be directly connected to CD players, tuners and tape recorders. * Tested with several headphone models of different impedance: 32, 100, 245, 300, 600 & 2000 Ohm. * Old 8 Ohm impedance headphones can be also driven, but these obsolete devices are not recommended. * Schematic shows left channel and power supply (common to both channels). * Numbers in parentheses show IC1 right channel pin connections. * A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 & C4. Then connect separately the input and output grounds to the power supply ground.

Regulator: This board supplies DAC board with +/- 15V for analog section. MUR860 in rectifier bridge, LM317 and Lm337 as regulator IC's and BG-STD at the output. LM317, LM337 power supply PCM2702: A little modified version of producent application. BlackGate-STD used in OPA2602 power supply, BG-N in analog and Sanyo OS-Cono in digital PCM section. At the output Panasonic FC.

The heart of this circuit is low-cost 16-bit Philips DAC. As a SPDIF decoder was chosen Cirrus Logic CS8412 IC with SN75179 as an input driver. Each IC have it's own AN800x regulator and there are separate wiring for analog and digital section.

I wanted to make this HI-FI Valve Amplifier so that MCS can be considered a classic brand like a lot, but my hand veteran tuner anfimden kopamıyordum transistor amplifier at the end of this one day I decided to take it in my hand as long as I have somehow amplifier kurtulamayacaktım air after breakfast and drinking my tea I gave trying to check if the decision is correct Cry with her ​​almost 15 years we have not shared this with less than animism, but cherish her ​​love of rock music by pressing the send us compelled to take this tube amplifier device bitirebilecektim yes, I was sure before I took a friend who wants to 3 months without music ... without it stood late Tagged with kamçılandım ITSELF HERE:)

This is an article about my new PCB design for CMoy headphone amplifier. Main feature is that the new PCB fits exactly to the classic Altoids tin-can. This new CMoy incorporates moreover bass-boost circuit and constant current charger for 9V battery.

The LM3886 is a high-performance audio power amplifier capable of delivering 68W of continuous average power to a 4? load and 38W into 8? with 0.1% THD+N from 20Hz–20kHz. The performance of the LM3886, utilizing its Self Peak Instantaneous Temperature SPiKe protection circuitry, puts it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area. SPiKe protection means that these parts are completely safeguarded at the output against over voltage, under voltage, overloads, including shorts to the supplies, thermal runaway, and instantaneous temperature peaks. The LM3886 maintains an excellent signal-to-noise ratio of greater than 92dB. It exhibits extremely low THD+N values of 0.03% at the rated output into the rated load over the audio spectrum, and provides excellent linearity with an IMD typical rating of 0.004%.

Simple Hybrid Headphone Amplifier DIY Audio Project. Rogers has put together a very simple hybrid headphone amplifier. The head amp uses a 12AU7/ECC82 vacuum tube for voltage gain stage and a IRF612 MOSFET follower biased in Class A with a passive CCS. What is nice about the project is that both the tube and MOSFET operate off of a 24V external switch mode power supply. Read on for more details about 12AU7 Tube / IRF610 MOSFET Hybrid Headphone Amplifier.

Here's a simple to build hybrid tube headphone amplifier built around 12AU7 / ECC82 vacuum tube. I have always been intrigued by tube amplifiers, but most DIY kits are very expensive and use very high voltage. So I decided to build an amplifier that would be inexpensive and had the least amount of parts necessary to drive a pair of 32 ohm Grado headphones. Having built several YAHA amps based on the fa-schmidt design, and a Szekeres Mosfet follower I wondered how the two would sound together. So I built the schematic into TINA-TI, a free spice based program to test circuits before the build, and the results were remarkable. Nearly 20dB of gain across 20Hz-100kHz from a 13VDC power supply. As you see in the schematic and parts list, there are less than 30 discrete components and most DIY'ers will have them as spares from other builds. I chose the 12AU7 / ECC82 vacuum tube because it can be driven with low voltage and the filament voltage is 12.6 volts, so there is no need to regulate the voltage any further. I used 1/4W resistors in the first stage and 2W in the second. The 2W resistors may be overkill but I did not want to change them later. The 20ohm resistor must be a minimum of 5W and do not use wire wound, as the inductive characteristics will distort the response curve.